Rheem Furnace Repair Nationwide

Rheem Furnace Repair in Orlando: What to Know First

Rheem furnace repair in Orlando typically runs between $150 and $700, and most jobs are completed in a single visit. We’re an independent Rheem service provider, not a manufacturer affiliate, which means we diagnose the actual problem before quoting anything, and you get a written price before we touch a single screw.

Call (850) 695-3178

This page is for Orlando homeowners with a Rheem furnace that’s acting up. Whether the burners won’t stay lit or the blower’s making a noise that keeps you up at night, you’ll find specific answers below, not generic filler. Need help right now? Call (850) 695-3178 and a real person picks up, 24/7.

How Rheem Products Fail – and How We Fix Them

• Rheem Classic Series (R801T, R802T): Ignitor failures that other techs misdiagnose as gas valve issues. These 80% AFUE single-stage furnaces use a silicon nitride hot surface ignitor that gets brittle after 6-9 years of Orlando’s humid-season cycling. The telltale: the furnace clicks, the draft inducer runs, but no flame catches. Many companies replace the gas valve first, which is a $350 mistake. We test ignitor resistance with a multimeter before recommending anything, and we keep Rheem-spec ignitors on the truck, so this is usually a same-visit fix.
• Rheem Prestige Series modulating furnaces (R97V, R96V): Pressure switch faults triggered by clogged condensate traps. These high-efficiency units condense moisture constantly, and Orlando’s dust plus our hard water leaves mineral buildup in the trap. The symptom: the furnace throws a pressure switch error code and locks out, especially after a cold snap when it hasn’t run in weeks. The fix is usually a thorough trap cleaning and a drainage check, not a switch replacement. We’ve seen homeowners pay twice for this repair because the first tech swapped the switch and never cleaned the line.
• Rheem Achieve Series (R95T): Flame sensor fouling from sulfur compounds in natural gas. Florida gas has trace sulfur that deposits on the flame sensor rod, and in the Achieve line the sensor sits in a position where carbon accumulates faster than on comparable Carrier units. The symptom: the furnace lights, runs for 3-6 seconds, then shuts off. The sensor just needs a proper cleaning with the right abrasive pad, not a replacement. This is a $150-$200 service call in most cases, and we can usually have it done in under an hour.
• Blower motor capacitor failures across Rheem’s mid-efficiency lines during Orlando’s shoulder seasons. Here’s the thing about Orlando: fall and spring mean your furnace cycles constantly, sometimes running five cycles a day. That start-stop stress kills capacitors. The symptom: you hear a hum, but the blower won’t spin, or the blower runs slow. We stock genuine Rheem capacitors and quality aftermarket equivalents, and we’ll tell you the difference in price and warranty before installing either one.
• Heat exchanger rust-through on 12-15 year old Rheem units near the coast. If you live on the east side of Orlando toward Christmas or Bithlo, you get more salt in the air than most homeowners realize. Combined with condensate, that accelerates heat exchanger corrosion on older Rheem Criterion and early 90 Plus units. The symptom: a faint metallic smell when the heat runs, or a visible crack during a seasonal inspection. We’ll scope the exchanger with a camera rather than guess. If it’s cracked, we tell you straight up whether a repair makes sense or if you’re better off putting that money toward a new system.

Our Rheem Furnace Repair Process

Here’s how a Rheem repair goes with us, start to finish:

1. 1
   Call or book online. You reach a live person or book through our site, and you’ll get a technician assigned with a live arrival time you can track, not a four-hour window. Andre Fuller built this system because he hates phone tag as much as you do.
2. 2
   We show up, introduce ourselves, and look at YOUR furnace, not the model number alone. We’ll ask about the symptoms, any error codes, and when it first started. We carry multimeters, manometers, and inspection cameras on every truck.
3. 3
   Diagnostic testing before any parts are touched. For a Rheem with a no-heat call, that means checking the ignitor resistance, the flame sensor signal, the gas pressure, and the control board error history. We don’t throw parts at a problem.
4. 4
   Written price for the exact fix. You’ll see the dollar amount, the part being replaced, and why. We’ll also tell you if we’re recommending OEM Rheem parts or a quality aftermarket equivalent, including the price difference and warranty difference. You approve it, or we pack up and leave. No pressure.
5. 5
   The repair plus a full system test. We don’t just replace the part and bounce. We run the furnace through multiple cycles, test the temperature rise across the heat exchanger, check the carbon monoxide reading, and make sure the drain lines are clear.
6. 6
   Your written guarantee before we leave. Every Rheem repair we complete includes a written guarantee. If it fails within the coverage window, we come back free. And our 365-Day Done Right Promise means if anything we touched isn’t right for a full year, you’re covered.

What Rheem Furnace Repair Costs in Orlando

Most Rheem furnace repairs in Orlando fall between $150 and $700. The spread exists because some problems are a 45-minute sensor cleaning and others require a new control board or gas valve. Here’s what common Rheem jobs actually run:

• Flame sensor cleaning or replacement: $150-$250
• Hot surface ignitor replacement: $200-$375
• Pressure switch diagnosis and repair: $180-$400
• Capacitor replacement: $175-$300
• Blower motor replacement: $450-$700
• Gas valve replacement: $350-$650
• Control board replacement: $400-$700

What moves the price: the part cost, the age of the unit, and how deep the diagnostic goes. We don’t mark up parts beyond reason and we don’t charge a separate diagnostic fee when you approve the repair. Every quote includes the labor in the price you see before we start. Call (850) 695-3178 for an exact quote on your Rheem, free.

Why Orlando Homeowners Call Halden Heating and Air Orlando for Rheem Work

We’re not the only HVAC company in Orlando, and we won’t pretend otherwise. But we do Rheem differently. Our techs know which Rheem models have which weak points, and we stock the common parts so you’re not waiting three days with a cold house while someone orders an ignitor. Every repair gets a written price first, a written guarantee after, and a free second visit if the repair fails within the coverage window. That’s wrapped into the 365-Day Done Right Promise, which is exactly what it sounds like: a full year of accountability on every job we finish.

We also service Carrier, Trane, and Lennox, so if you’ve got a mixed system or you’re thinking about replacing the Rheem down the road, we can handle it. Andre Fuller set up Halden Heating and Air Orlando around one rule: tell you what it costs, tell you what’s broken, then we fix it. In that order. No door-step price changes, no vague arrival windows, and no voicemail trees when your heat dies at 11 p.m.

FAQs