Furnace & heating
AC repair
Heat pumps
Ductless mini splits
Carrier
Trane
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateBryant Heat Pump Service: The Orlando Owner’s Guide
We stock Bryant-compatible parts on our trucks and install them same-day in most Orlando neighborhoods, with typical heat pump repairs running $150 to $650 depending on the part. Book online, get a live arrival time, and track your tech to the door. Here’s how it usually plays out: your Bryant heat pump has been running fine, then one afternoon you notice the air coming out of the vents feels lukewarm, or the outdoor unit is making a noise it never made before. Maybe the system short-cycles (kicks on, runs three minutes, shuts off) and your energy bill has crept up. That’s the moment most Orlando homeowners realize a component inside that Bryant unit has reached the end of its run, and they need a service call from someone who actually knows Bryant equipment.
Which Bryant Models This Applies To
This service coverage applies to Bryant’s Evolution, Preferred, and Legacy heat pump lines: the Evolution 280A and 288BNC variable-speed units, the Preferred 226C and 227T two-stage systems, and the Legacy 214D and 215B single-stage heat pumps. Crucial compatibility gotcha most people don’t know: Bryant heat pumps built after 2019 often use communicating control boards that must be matched by model number, not by “close enough.” We verify the exact board revision before ordering so you aren’t paying for a part that won’t talk to your thermostat. Another Orlando-specific factor: our humidity and salt air in neighborhoods near the coast or lakes like Conway, Dr. Phillips, and Baldwin Park corrode condenser coils and contactors faster than in drier climates. Halden Heating and Air Orlando is an independent service provider, not affiliated with Bryant, and we also stock parts for Carrier, Trane, and Lennox. On OEM versus aftermarket: Bryant factory parts (through Carrier’s parts network) carry the manufacturer warranty and exact spec fit, while quality aftermarket equivalents (contactors, capacitors, defrost sensors) often cost 20% to 30% less and perform identically. For control boards and variable-speed motors, we recommend OEM every time.
Styles & brands we work with
Signs Your Bryant Heat Pump Service Is Failing
- Weak or warm airflow while the outdoor unit runs constantly. This usually points to a failed run capacitor or a refrigerant leak in the evaporator coil. The compressor is working, but it can’t move heat effectively.
- Short-cycling: the unit starts, runs briefly, then shuts off. In Orlando this is frequently a dirty or failing condenser coil combined with high head pressure. The system shuts down to protect itself, which is why it never seems to finish a full cycle.
- Grinding, screeching, or rattling from the outdoor unit. A failed fan motor bearing or a dying compressor makes distinct sounds. Rattling often means the compressor mounts have worn. Grinding usually means you’re on borrowed time.
- Frozen coil even when it’s warm outside. If you see ice on the outdoor unit coil in Orlando heat, you’ve got a defrost control board or defrost thermostat failure, or low refrigerant. The unit literally can’t shed ice even when ambient temps are in the 80s.
- Higher energy bill with no change in thermostat setting. A failing compressor run capacitor makes the compressor work harder and draw more amperage. In Florida where heat pumps run nearly year-round, that inefficiency shows up fast on your OUC or Duke Energy bill.
See the difference
Before
After
Before
After
Before
AfterReplacement Cost & What’s Included
Most Bryant heat pump repairs in the Orlando market run between $150 and $650, parts and labor included. Here’s what drives that range:
| Part | Typical Installed Range |
|---|---|
| Run or start capacitor | $150 – $250 |
| Contactor | $150 – $275 |
| Defrost control board or sensor | $200 – $400 |
| Condenser fan motor | $350 – $550 |
| Reversing valve | $550 – $650 |
| Compressor (when replacement makes sense) | $1,200 – $2,800 |
Every quote comes as a written price before any work starts, with parts and labor broken out. No door-step price changes, no “well, while we’re in there” upcharges. Every repair includes a written guarantee, and if it fails within the coverage window, we come back at no charge. That free second visit is automatic because the 365-Day Done Right Promise is built into how we work, not sold as an add-on.
DIY or Call Us?
Some things are safe to check yourself. You can confirm your thermostat is set correctly, check that the air filter isn’t clogged, and verify the breaker hasn’t tripped. You can also visually inspect the outdoor unit for obvious debris, a frozen coil, or a capacitor with a swollen top. Here’s what you should not do: Bryant heat pumps carry high voltage even when the unit is off, and capacitors store enough charge to hurt you badly. A failed capacitor, contactor, or defrost board is not a safe DIY swap. What most DIY attempts actually produce is a $650 repair becoming a $2,000 repair because a shorted wire fried the control board. Andre Fuller grew up in Los Angeles and trained at Los Angeles Trade-Technical College, and after more than two decades turning wrenches, his rule hasn’t changed: tell you what’s broken, tell you what it costs, then fix it. In that order. If your Bryant heat pump is acting up, call (850) 695-3178 and we’ll get someone out with the right part on the truck.
FAQs
Most Bryant heat pump components last 10 to 15 years in Florida, but Orlando’s humidity and summer heat load compress that timeline for parts like capacitors and contactors, which often fail in 5 to 8 years. Salt air near the coast shortens lifespan further. Call (850) 695-3178 if you’re not sure whether a part is at the end of its run.
Some parts, like a contactor or capacitor, are replaced outright because rebuilding them makes no economic sense. Components like fan motors or control boards are also swap-outs. The only part we usually repair rather than replace is a leaking coil, and even then, replacement is often cheaper long-term. We’ll give you a written price either way before anyone touches a screw.
Most single-part replacements like a capacitor or contactor take 45 to 90 minutes from arrival to test-run. More involved jobs like a reversing valve or compressor can take 3 to 6 hours. We give you a live arrival time before we show up, not a four-hour window.
Yes, our trucks carry the most common Bryant heat pump parts for Orlando service calls: run capacitors, contactors, defrost sensors, fan motors, and select control boards. For less common parts like reversing valves for a specific Evolution series model, we source from Bryant’s distribution network same-day in most cases.
If your Bryant heat pump is misbehaving, call Halden Heating and Air Orlando at (850) 695-3178 for a free estimate and a live arrival time. We’ll show you who’s coming, when they’ll arrive, and what it costs before any work begins.
Written by Andre Fuller, Owner & Lead HVAC Technician, Halden Heating and Air Orlando at Halden Heating and Air Orlando, serving Orlando and nearby areas.